帶 * 為必填項 關閉
PP耐酸堿移印油墨
訂貨量(千克)
價格(不含稅)
1
200.00元/
10
180.00元/
供應標題:PP耐酸堿移印油墨
價格:電儀
發布公司:上海凱賢印刷科技有限公司
供貨總量:10000
聯系人:楊洪
發貨地點:上海 上海 上海市
發布時間:2024年01月05日
有效期至:2024年03月05日
在線詢盤:在線詢盤
產品綜合信息質量:未計算
基本信息
PP耐酸堿移印油墨
歐萊斯PP系列油墨是采用進口原材料及顏料經技術中心反復測試調制而成的PP免處理高性能油墨,油墨墨層柔軟度好、富彈性、耐磨損,對于未處理PP料通用性好,具有耐熱油、耐汗液、耐酸堿、高抗刮性、高耐醇、高耐磨、耐水煮、流動性好,可絲印和移印等特點。
【適用材料】
PP料、處理過之PE料、尼龍料及類似材料
【產品舉例】
玩具、洗發水瓶、化妝品瓶、奶瓶、水杯、果汁機、豆?jié){機、洗碗機等
【基本性能】
承印物:未處理的半透明PP水杯、印刷后自干24小時測試
檢測項目 | 測試方法、條件 | 測試結果 |
酒精測試 | 用加載500克力的粘酒精(99.7%)棉布來回平推 | 100次不露底 |
附著力測試 | 百格法:劃1mm×1mm #格 用3M膠紙以90度直角剝離5次 | 無脫落 |
耐摩擦 | 用加載500克力的普通橡皮來回平推 | 100次不露底 |
耐火機油 | 用加載500克力的粘機油棉布來回平推 | 30次不露底 |
耐水煮 | 100℃煮1小時 | 仔細觀察,印刷字體和圖案顏色無變化 |
【使用說明】
網板:250—350目聚脂絲網印版膠刮:建議使用65-80度聚氨酯膠刮參考用量:300目網板印刷約為35㎡/㎏選用稀釋劑:S-91絲印稀釋劑、S-81移印稀釋劑網板清洗:選用有機溶劑清洗(如:洗網水)
【干燥條件】
自然揮發干燥:表干5分鐘,完全干燥48小時或者烘烤85-100℃ 40分鐘(烘烤溫度較高時,可適當減少烘烤時間)PE料、尼龍料、有添加口水雜料或有蠟層的PP料建議烘烤附著性更佳。
【固化劑】
對PE料和部分雜料之PP料,可能會出現附著力差等現象,可選用本公司PPA-34處理劑擦拭或添加T-2M固化劑10%進行加溫烘烤,以增強其附著力。
【注意事項】
1、塑膠產品具有多樣性,材料外觀相似但可能是不同的材料,建議做好測試再進行印刷
2、對于表面張力較小的材料,可先用PP處理劑或火焰處理法對底材進行處理后印刷,這樣可以提高油墨的附著力。
3、該油墨屬于慢反應固化型油墨,測試附著力必需在印刷后24小時以上再進行測試。
4、PP油墨顯酸性,用于移印時,如果油墨長時間浸泡覆蓋鋼板可能對鋼板有輕微的腐蝕。
5、銀色、金色建議低溫(10℃以內)保存,在常溫下保存的時間相對較短,一般不超過1個月。
The rice PP series of ink is the use of imported raw materials and pigment by the technology center of repeated testing of modulated PP free high performance ink, ink layer, good softness, flexibility, abrasion resistance, for the untreated PP material has good universality, is heat oil, sweat resistance, acid and alkali resistance, high scratch resistance, high alcohol, high wear resistance, boiling water resistance, good fluidity, screen printing and pad printing etc..
[applicable materials]
PP material, treated PE, nylon and similar materials
[product example]
Toys, shampoo bottles, cosmetic bottles, bottles, water cups, juice machines, soya bean milk machines, dishwashers, etc.
[basic performance]
Substrate: untreated translucent PP cup, printed after 24 hours of dry test
Test item
Test methods and conditions
test result
Alcohol test
With 500 grams of alcohol loaded adhesive (99.7%) to push back cotton
Do not open at the end of 100
Coating Adhesion Test
100 lattice method: row 1mm * 1mm # lattice with 3M tape to a 90 degree angle off 5 times
No shedding
Friction resistance
By loading 500 grams of ordinary rubber to push back
Do not open at the end of 100
Fire-resistant oil
With sticky cotton oil loading 500 grams and flat push
Do not open at the end of 30
Boiling resistance
Cook for 1 hours at 100
Close observation shows no change in the color of the print and pattern
[instructions for use]
Mesh plate: 250 - 350 mesh polyester screen plate
Squeegee: it is recommended to use 65-80 degree polyurethane squeegee
Dosage: 300 mesh screen printing is about 35 kg / square meters
Choose thinner: S-91 screen thinner, S-81 printing thinner
Screen cleaning: the use of organic solvents cleaning (such as: washing mesh water)
[drying conditions]
Natural dry: dry for 5 minutes, completely dry 48 hours or 40 minutes (C 85-100 baking baking temperature is high, may be appropriate to reduce the baking time) PE material, nylon material, adding complex material or PP material slobber suggest baking wax layer adhesion.
[curing agent]
For PE materials and some miscellaneous materials of PP material, there may be poor adhesion, and so on, we can choose our company PPA-34 treatment agent to wipe or add T-2M curing agent 10% for heating baking, so as to enhance its adhesion.
[matters needing attention]
1, plastic products are diverse, similar material appearance, but may be different materials, it is recommended to do the test and then print
2, for the less surface tension of the material, you can first use PP treatment agent or flame treatment method for the substrate after processing printing, so as to improve the adhesion of the ink.
3, the ink belongs to slow response curing ink, test adhesion must be printed after more than 24 hours and then tested.
4, PP ink acid, used for pad printing, if the ink for a long time to cover the steel plate, may have slight corrosion of steel plate.
5, silver, gold, recommended low temperature (10 degrees Celsius) preservation, at room temperature preservation time is relatively short, generally not more than 1 months.
上海凱賢印刷科技有限公司基本信息
員工人數:10-50人 廠房面積: 年營業額:人民幣10萬元/年-人民幣30萬元/年
年進口額:人民幣30萬元/年-人民幣50萬元/年 年出口額:人民幣30萬元/年-人民幣50萬元/年 主要市場:大陸,港澳臺地區,全球,
客戶群:
公司名稱:上海凱賢印刷科技有限公司
注冊資本:人民幣10萬元/年-人民幣30萬元/年 公司網址:http://kx9966.glass.com.cn主營產品:金屬自干油墨,玻璃油墨,陶瓷油墨,不銹鋼油墨,ABS油墨,絲印油墨,移印油墨,絲印網版 公司成立年份:2009
公司網址:http://kx9966.glass.com.cn
產品屬性:
計量單位:千克 供貨總量:10000 最小起訂量:1 產品單價:200.00 品牌: 規格型號: 包裝說明: